1. Computer Repair
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.abrt.com/computer-repair
2. Bearing NSK
Single-Row Deep Groove Ball Bearings. Pressed Steel Cages. Single-row deep groove ball bearings are the most common type of rolling bearings. Their use is very widespread. In addition to open type bearings, these bearings often have steel shields or rubber seals installed on one or both sides and are prelubricated with grease. Also, snap rings are sometimes used on the periphery. As to cages, pressed steel ones are the most common. For big deep groove ball bearings, machined brass cages are used. Machined cages are also used for high speed applications.
http://ball-bearings.online
3. Sealed Bearings
Sealed bearings. A selection of SKF spherical roller bearings is also produced in a sealed version with contact seals on both sides. The seals are reinforced with sheet steel and made of an oil and wear-resistant: acrylonitrile-butadiene rubber (NBR), designation suffix 2CS; hydrogenated acrylonitrile butadiene rubber (HNBR), designation suffix 2CS5; fluoro rubber (FKM), designation suffix 2CS2. The seals are inserted in recesses in the outer ring. For smaller bearing sizes, the seals are pressed into the recesses while the seals for the larger sizes are held in position by means of retaining rings (fig). The seals have two sealing lips contacting the lead-in at the sides of the inner ring raceway, to provide efficient sealing. Sealed bearings are lubricated as standard with an extreme pressure bearing grease according to table 1. They should not be heated to temperatures above 80°C during mounting, and should not be washed. Sealed bearings do not need to be relubricated when the operating temperature does not exceed 70°C and the rotational speed is below 50% of the limiting speed listed in the product table. When temperature and/or speeds are high, relubrication with a similar grease with lithium thickener is recommended. In this case the polymer band, which covers the lubrication holes in the outer ring must be removed before mounting. Note that only a small amount of grease is needed to relubricate sealed bearings. The grease should be pressed in slowly through the lubrication holes in the outer ring while the bearing is rotating. Excessive pressure should be avoided so as not to damage the seals. The internal design of a sealed bearing corresponds to that of an open bearing. The external dimensions are also the same except for bearings based on the 222 and 223 series. These bearings are slightly wider and carry the series designation BS2-22 and BS2-23 respectively. Sealed bearings are available with a cylindrical bore as standard. However most bearings in the BS2-22 series are available with a tapered bore as well. Every sealed bearing can be supplied with a tapered bore to special order. To prevent interference with the seal, the diameter of the shaft abutment should not exceed damax at least for the 1 to 2 mm closest to the bearing. If the bearings are secured axially on the shaft by a lock nut, SKF recommends using a KMFE lock nut or to position an intermediate ring between the bearing and the lock nut.
http://ball-bearings.online
4. Stainless Steel Pipes
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
5. SKF Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
6. Stainless Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/stainless-steel-forging
7. Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/steel-forging
8. Computer Repair
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.1t-s.com/computer-repair
9. Doncaster Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://doncaster.open-source.1t-s.com
10. Rotherham Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.bespoke-software.1tsolutions.com
11. Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.open-source.1t-s.com
12. Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
13. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.application-development.1tsolutions.com
14. Pillow Block Bearings
Plummer block roller bearing units. SKF roller bearing units (mounted bearings) with a plummer (pillow) block housing are available as: metric SKF ConCentra units; inch SKF ConCentra units; units with a locking collar. SKF ConCentra units in the SYNT series replace the former SKF ConCentra units in the SYT series. All plummer block roller bearing units comprise: a plummer block housing; an SKF spherical roller bearing in the 222 series; a stepped sleeve or locking collar; an integral seal fitted on both sides; lubricant. When compared to sleeve-mounted bearing units in split housings, SKF ConCentra units provide a number of advantages including: longer service life; higher operational reliability; quicker mounting; minimal maintenance; simplified replacement.
http://ball-bearings.online
15. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.bespoke.software.1t-s.com
16. 316 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
17. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.software.development.grid-itc.com
18. Computer Repair
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://grid-itc.com/computer-repair
19. Waste Recycling System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-system.skip-manager.com
20. Bearings for Volvo Trucks
Volvo Trucks, a subsidiary of the Swedish automotive manufacturer Volvo Group, has a rich history in the production of heavy-duty trucks. Volvo Trucks was founded in 1928 in Gothenburg, Sweden, as a subsidiary of AB Volvo. The first Volvo truck, the Series 1, was introduced in 1928. It had a 2-ton payload capacity and featured innovative features for its time. Throughout the 1930s and 1940s, Volvo Trucks continued to develop and expand its truck lineup, focusing on durability and reliability. In the 1970s, Volvo Trucks expanded its presence globally, establishing production facilities and sales networks in different countries. In 1984, Volvo Trucks introduced the groundbreaking Volvo F10 and F12 trucks, known for their advanced features and fuel efficiency. In 2001, Volvo Trucks became part of the newly formed Volvo Group, which brought together various divisions of the Volvo brand. In recent years, Volvo Trucks has embraced electric and alternative fuel technologies, developing electric and hybrid truck models and investing in sustainable transportation solutions. Volvo Trucks has been at the forefront of developing autonomous and connected truck technologies. The company has demonstrated self-driving trucks in various pilot projects and continues to invest in research and development in this area. Volvo Trucks also offers connected services and telematics solutions to enhance fleet management and optimize vehicle performance.
http://https://ball-bearings.online/oem/volvotn/products
21. Stainless Steel Valves
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://valves.stainless-steel.zx55.com
22. Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.abrt.com/computer-services
23. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.custom.software.abrt.com
24. Rotherham eCommerce
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.1t-s.com/internet-web-design
25. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.sanitary-fittings.stainless-steel.zx55.com
26. Skip Manager
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-manager.co.uk
27. Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
28. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.bespoke-software.1tsolutions.com
29. South Yorkshire Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.south-yorkshire.open-source.1t-s.com
30. Y-bearings with a hexagonal or square bore
Y-bearings in the YHB 2 and YHC 2 series with a hexagonal bore and in the YQC 2 series with a square bore are intended primarily for use in applications, where high torques have to be transmitted. The bore is produced to a plus tolerance and allows easy mounting and dismounting. These bearings are axially located on the shaft using adjacent components. The standard outer ring, which has a convex sphered outer surface and no lubrication holes, is identified by the suffix W. YHB 2 and YHC 2 bearings Bearings with a hexagonal bore are filled with a special VT357 specification grease (see section "Grease fill"). They are fitted with the rugged LS8 contact seal, which rides on the ground surface of the inner ring shoulder . In cases where there is a lubrication hole in the outer ring, the suffix W is omitted from the bearing designation. YQC 2 bearings. Bearings with a square bore are equipped with a highly efficient triple lip contact seal, which rides on the ground surface of the inner ring shoulder . These bearings are filled with the standard grease (see section "Grease fill"). Bearings having a cylindrical outer surface are also available and identified by the suffix C, e.g. YQC 208-102 CW.
http://ball-bearings.online?pg=rb-yb-hsb
31. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1tsolutions.com/application-development
32. High Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
33. Stainless Steel Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
34. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application.development.abrt.com
35. Stainless Steel Flanges
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
36. Drop Forging
Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.
http://www.ktforge.co.uk/drop-forging
37. Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.hygienic-fittings.stainless-steel.zx55.com
38. South Yorkshire Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.application.development.abrt.com
39. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1t-s.com/application-development
40. Sheffield Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.sheffield.computer.service.1t-s.com
41. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://huddersfield-university-accomodation.iam4rent.co.uk/
42. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/
43. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1tsolutions.com/software-development
44. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/student-accomodation-huddersfield
45. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.bespoke.software.grid-itc.com
46. Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
47. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1tsolutions.com/software-development
48. Barnsley Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.bespoke.software.grid-itc.com
49. Rod End Bearings
Spherical plain bearings and rod ends. In addition to ball and roller bearings SKF also produces a comprehensive range of spherical plain bearings and rod ends and has a choice of materials for plain and flanged bushings as well as thrust washers. Spherical plain bearings and rod ends are produced in various designs and with various combinations of sliding contact surfaces. Each design and combination has characteristic properties which make it particularly suitable for certain applications. To select a certain bearing type and to establish the requisite bearing size, the main factors which have to be considered are the loads, the load carrying capacity of the bearing and the expected service life. The same is true when selecting a rod end. Selection of bearing type. The choice of the appropriate type of bearing (radial, angular contact or thrust) is determined by the direction of the load which will act on the bearing, while the choice of the appropriate sliding contact surface combination is primarily determined by the way in which the load acts (constant or alternating direction). Radial load: When the load is purely or predominantly radial, a radial spherical plain bearing should be selected. These bearings can accommodate a certain amount of axial load in addition to the radial load. Axial load: When the load is purely or predominantly axial then the choice should be a spherical plain thrust bearing. These bearings can accommodate a certain proportion of radial load in addition to the axial load.
http://ball-bearings.online
50. Sheffield Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://sheffield.open-source.1t-s.com
51. Waste Collection System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-collection-system.skip-manager.co.uk
52. Cold Forging
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://www.kt-forge.co.uk/cold-forging
53. Barnsley eCommerce
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.1t-s.com/internet-web-design
54. Rooms For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/rooms-for-rent-huddersfield
55. Skip Manager
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-manager.com
56. Stainless Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://stainless-steel-forging.ktforge.co.uk
57. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.software.devlopment.1tsolutions.com
58. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/house-for-rent-huddersfield
59. SKF Bearings Catalogue
The SKF online catalogue provides fast and easy access to parts and technical information. Features available through the SKF online catalogue range from basic product search to viewing product pictures, engine layouts, technical bulletins and much more. The SKF product portfolio. SKF has a reputation for manufacturing high quality bearings. Most of our bearing and seal products are described in the SKF Interactive Engineering Catalogue. Information about other products may be included in other SKF websites. The left hand menu guides you to the right starting point. You can find online tools for product selection, and installation and maintenance in the library. Products for specific industries and applications. If you are looking for a product for a certain industry or application (for example a seal for a slurry pump), go to industries. This is a way to find the product and service solutions specific to your needs. The SKF services portfolio. If you are looking for advice and services in the areas of engineering consultancy, logistics, asset management, condition monitoring, mechanical maintenance, remanufacturing, or training, go to services.
http://ball-bearings.online
60. Rotherham Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.bespoke.software.abrt.com
61. Waste Recycling System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-recycling-system.skip-manager.co.uk
62. Forging Stainless Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/forging-stainless-steel
63. Sockolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
64. Skip Hire Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-hire-software.skip-manager.co.uk
65. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/student-accomodation-huddersfield
66. Chesterfield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.bespoke.software.grid-itc.com
67. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.software.devlopment.1tsolutions.com
68. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.software-development.1tsolutions.com
69. Doncaster Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://doncaster.linux.1t-s.com
70. Upset Forging
Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.
http://www.kt-forge.co.uk/upset-forging
71. Rotherham Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.custom.software.abrt.com
72. SKF Bearings
SKF has a reputation for manufacturing high quality bearings. Most of our bearing and seal products are described in the SKF Interactive Engineering Catalogue. Information about other products may be included in other SKF websites. The left hand menu guides you to the right starting point. You can find online tools for product selection, and installation and maintenance in the library. Products for specific industries and applications. If you are looking for a product for a certain industry or application (for example a seal for a slurry pump), go to industries. This is a way to find the product and service solutions specific to your needs. The SKF services portfolio.
http://ball-bearings.online
73. Smith Forging
Forging worked between flat or simple contour dies by repeated strokes and manipulation of the workpiece. Also known as "hand" or "flat die " forging.Heavy workpieces could be processed using a smith-forging hammer, and smaller forgings are die formed in drop hammers. Smith forging hammers are typically steam or air-operated, consisting of a power actuated ram supported by a heavy cast iron frame. The final product is a result of the ram being powered into the dies containing the workpiece.
http://smith-forging.ktforge.co.uk
74. Waste Recycling Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-software.skip-manager.co.uk
75. Hammer Forging
The most common type of forging equipment is the hammer and anvil. Principles behind the hammer and anvil are still used today in drop-hammer equipment. The principle behind the machine is simple: raise the hammer and drop it or propel it into the workpiece, which rests on the anvil. The main variations between drop-hammers are in the way the hammer is powered; the most common being air and steam hammers. Drop-hammers usually operate in a vertical position. The main reason for this is excess energy (energy that isn't used to deform the workpiece) that isn't released as heat or sound needs to be transmitted to the foundation. Moreover, a large machine base is needed to absorb the impacts. To overcome some shortcomings of the drop-hammer, the counterblow machine or impactor is used. In a counterblow machine both the hammer and anvil move and the workpiece is held between them. Here excess energy becomes recoil. This allows the machine to work horizontally and have a smaller base. Other advantages include less noise, heat and vibration. It also produces a distinctly different flow pattern. Both of these machines can be used for open-die or closed-die forging. A forging press, often just called a press, is used for press forging.
http://hammer-forging.ktforge.co.uk
76. Computer Maintenance
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://1t-s.com/computer-maintenance
77. Waste Collection System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-collection-system.skip-manager.co.uk
78. Sockolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
79. SKF Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
80. Sheffield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.custom.software.grid-itc.com
81. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://application.development.1t-s.com
82. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.application.development.abrt.com
83. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.custom.software.1t-s.com
84. Scooter Bearings
If you have plastic core scooter wheels then fitting the bearings is very straight forward as they typically can be pushed in by hand without issue. Fitting scooter bearings into Metal core wheels is a little trickier as they are designed to be a tight fit so pushing them in by hand rarely works. In our workshop we used to use a vise to gently squeeze them in, but now we use a hammer!! Apply a small amount of grease to the edges of each bearing you are going to install. Apply a small amount of grease to the inside hole on the scooter wheel where the bearings are going to be fitted. Place the bearing over the hole in the wheel and try and make sure that it is straight/level as possible. Place either a block of wood or an old paperback book over the top of the bearing and gently strike this with the hammer (Important - do not strike the bearing directly with the hammer). When the bearing has been hammered in fully into the hole in the middle of your wheel it should sit flush with the edge of the wheel Turn the wheel over and insert the bearing spacer (you will need a bearing spacer, if you do not use one your wheel will not spin when you do your axles up securely!)
http://ball-bearings.online
85. Stainless Pipe Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.stainless-pipe-supplier.zx55.com
86. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.software.devlopment.grid-itc.com
87. Accounts Software for Stockists
Designed for steel stock holders, SASS is a muli-currency accounts system which is ideal for all stockists incorporating Sales, Purchase & Nominal ledgers, Stock Control with emphasis traceability and profits based on actual / real costs ...
http://steelaccounts.com/
88. Stainless Steel Tubing
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://tubing.stainless-steel.zx55.com
89. Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://hygienic-fittings.stainless-steel.zx55.com
90. Cold Forming
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://cold-forming.kt-forge.co.uk
91. Stainless Steel Low Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
92. Drop Forging
Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.
http://www.kt-forge.co.uk/drop-forging
93. House to Share Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.student-housing-huddersfield.co.uk/
94. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.software.devlopment.abrt.com
95. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://house-for-rent-huddersfield.iam4rent.co.uk/
96. Stainless Pipe Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
97. Jamat Times
Jamat Times, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Salah Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.
http://www.jamat-times.com
98. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://grid-itc.com/computer-support
99. Chesterfield Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://chesterfield.linux.1t-s.com
100. Computer Maintenance
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.1t-s.com/computer-maintenance
101. Open Die Forging
Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.
http://open-die-forging.kt-forge.co.uk
102. Hot Forming
Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.
http://hot-forming.ktforge.co.uk
103. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.grid-itc.com/software-development
104. Wheel Bearings
Over time, wheel bearings suffer the effects of wear and tear. Water in particular takes its toll on them, making then rust or spoiling the grease that surrounds them. Wheel bearings allow your wheels to turn smoothly and also support the weight of the vehicle. If you're noticing alignment problems, your wheels are making a rumbling sound or the steering seems to have too much 'play' then you may have a wheel bearing problem and they may not be doing their job correctly. For quality wheel bearings for any car, check on line at eurocarparts.com and head off the danger of serious damage before it's too late.
http://ball-bearings.online
105. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/student-accomodation-huddersfield
106. Steel City Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
107. Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.1t-s.com/computer-services
108. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1tsolutions.com/bespoke-software
109. Iveco Truck Bearings
Iveco, an acronym for Industrial Vehicles Corporation, is a multinational manufacturer of commercial vehicles and diesel engines.Iveco was formed in 1974 through the merger of five European companies: Fiat Veicoli Industriali (Italy), OM (Italy), Lancia Veicoli Speciali (Italy), Unic (France), and Magirus-Deutz (Germany). The merger aimed to create a unified entity that could compete on a global scale in the commercial vehicle market. Following the merger, Iveco expanded its product portfolio and manufacturing capabilities, introducing a wide range of commercial vehicles, including trucks, buses, and industrial vehicles. In the 1980s, Iveco acquired several other companies, including Seddon Atkinson (UK) and Pegaso (Spain), further expanding its presence in the European market. During the 1990s and 2000s, Iveco focused on global expansion and diversification, establishing manufacturing facilities and sales networks in various countries outside Europe. In recent years, Iveco has continued to emphasize innovation and sustainability in its product development. The company has introduced advanced technologies, such as telematics systems and connectivity features, to improve vehicle performance, efficiency, and safety. Iveco has also focused on developing eco-friendly solutions, including hybrid and electric vehicles, to address the growing demand for sustainable transportation.
http://ball-bearings.online/oem/iveco/products
110. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1t-s.com/software-development
111. Sheffield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.application.development.grid-itc.com
112. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://software.development.grid-itc.com
113. Barnsley Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.custom.software.grid-itc.com
114. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.bespoke.software.abrt.com
115. Rooms For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://rooms-for-rent-huddersfield.iam4share.co.uk/
116. Student Diggs in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.student-housing-huddersfield.co.uk/
117. Roller Bearings
A roller bearing is a type of rolling element bearing that is used to reduce friction and support loads in rotating machinery. Unlike ball bearings, which use balls as the rolling elements, roller bearings use cylindrical or tapered rollers. There are different types of roller bearings, including cylindrical roller bearings, tapered roller bearings, spherical roller bearings, and needle roller bearings. Each type has its own specific design and is suitable for different applications and load conditions.
http://ball-bearings.online/categories/roller-bearings?id_category=10
118. Computer Repair
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://abrt.com/computer-repair
119. Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
120. South Yorkshire Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.south-yorkshire.linux.1t-s.com
121. WhoIs Lookup
The Detailed WhoIs tool not only checks the domain or IP address you request, but also looks up details of any associated domains and IP addresses, building a comprehensive report.
http://whois.1t-s.com
122. Doncaster Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.software.devlopment.grid-itc.com
123. Bulk Bearings
We purchase bearings and transmission products in bulk. If you would like to dispose of surplus or bankrupt stock, sell in bulk or just clear some of your inventory, we would like to hear from you.
http://www.surplus-bearings.co.uk
124. Roll Forging
Roll forging is a process where round or flat bar stock is reduced in thickness and increased in length. Roll forging is performed using two cylindrical or semi-cylindrical rolls, each containing one or more shaped grooves. A heated bar is inserted into the rolls and when it hits a stop the rolls rotate and the bar is progressively shaped as it is rolled through the machine. The piece is then transferred to the next set of grooves or turned around and reinserted into the same grooves. This continues until the desired shape and size is achieved. The advantage of this process is there is no flash and it imparts a favorable grain structure into the workpiece. Examples of products produced using this method include axles, tapered levers and leaf springs.
http://roll-forging.kt-forge.co.uk
125. Triumph Motor Vehicle Bearings
The history of the Triumph brand spans over a century and includes a rich legacy in the motorcycle and automobile industries. The Triumph brand was founded in 1885 by Siegfried Bettmann, a German immigrant, in Coventry, England. Initially, Triumph focused on manufacturing bicycles and bicycle parts. The company quickly gained popularity and expanded its production capacity. In 1902, Triumph produced its first motorcycle, a 2.2 horsepower model powered by a Belgian Minerva engine. After World War II, Triumph concentrated solely on motorcycle production and became one of the most prominent motorcycle manufacturers in the world. The 1950s and 1960s were a golden era for Triumph motorcycles, with iconic models like the Triumph Bonneville, Triumph Tiger, and Triumph Trident gaining widespread popularity. Triumph motorcycles achieved considerable success in racing, including victories at the Isle of Man TT races and other prestigious competitions. In the 1970s, Triumph faced financial difficulties and changing market dynamics, which led to the closure of its motorcycle division in 1983. However, the Triumph brand was resurrected in 1984 when businessman John Bloor acquired the rights to the name and established Triumph Motorcycles Ltd. Under Bloor's leadership, Triumph underwent a revival, focusing on modernizing its product lineup, improving quality, and leveraging its heritage. Triumph Motorcycles Ltd. re-entered the motorcycle market in 1990 and has since become a prominent player in the industry. The company expanded its product range, offering a diverse lineup of motorcycles across various categories, including cruisers, sport bikes, adventure bikes, and modern classics. Triumph has gained recognition for its distinctive designs, advanced engineering, and performance-oriented motorcycles.
http://ball-bearings.online/oem/triumph/products
126. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.custom-software.1tsolutions.com
127. Stainless steel deep groove ball bearings
SKF stainless steel deep groove ball bearings are resistant to corrosion from moisture and several other media. These single row deep groove ball bearings have the same deep raceway grooves and close conformity between raceways and balls as standard deep groove ball bearings made of carbon chromium (rolling bearing) steel. They are without filling slots and can carry axial loads acting in both directions in addition to radial loads, even at high speeds. SKF stainless steel deep groove ball bearings have the same running properties as conventional steel deep groove ball bearings, but have a lower load carrying capacity. The bearings are available in open and sealed designs for shaft diameters from 1 to 50 mm. SKF stainless steel bearings are identified by the designation prefix W, e.g. W 626-2Z.
http://ball-bearings.online?pg=rb-dgbb-ss
128. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://software.development.1t-s.com
129. South Yorkshire Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.software.devlopment.1t-s.com
130. Sheffield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.custom.software.1t-s.com
131. Student Diggs in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://student-diggs-huddersfield.iam4share.co.uk/
132. Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.linux.1t-s.com
133. Taper Bearings
Tapered roller bearings are bearings that can take large axial forces (i.e., they are good thrust bearings) as well as being able to sustain large radial forces. The inner and outer ring raceways are segments of cones and the rollers are also made with a taper so that the conical surfaces of the raceways and the roller axes if projected, would all meet at a common point on the main axis of the bearing. This conical geometry is used as it gives a larger contact patch, which permits greater loads to be carried than with spherical (ball) bearings, while the geometry means that the tangential speeds of the surfaces of each of the rollers are the same as their raceways along the whole length of the contact patch and no differential scrubbing occurs. When a roller slides rather than rolls, it can generate wear at the roller-to-race interface, i.e. the differences in surface speeds creates a scrubbing action. Wear will degenerate the close tolerances normally held in the bearing and can lead to other problems. Much closer to pure rolling can be achieved in a tapered roller bearing and this avoids rapid wear. The rollers are guided by a flange on the inner ring. This stops the rollers from sliding out at high speed due to their momentum. The larger the half angles of these cones the larger the axial force that the bearing can sustain. Tapered roller bearings are separable and have the following components: outer ring, inner ring, and roller assembly (containing the rollers and a cage). The non-separable inner ring and roller assembly is called the cone, and the outer ring is called the cup. Internal clearance is established during mounting by the axial position of the cone relative to the cup.
http://ball-bearings.online
134. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.software.development.1t-s.com
135. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.application-development.1tsolutions.com
136. Tapered Bearings
Tapered bearings, also known as tapered roller bearings, are a type of rolling element bearing that can support both radial and axial loads. They are designed with tapered inner and outer races and tapered rollers. The shape of the components allows for efficient distribution of the load and helps to accommodate axial and radial forces simultaneously. Tapered bearings are commonly used in applications where there are significant axial and radial forces, such as in automotive wheel hubs, heavy machinery, gearboxes, and axle systems. They are known for their durability, reliability, and ability to handle high loads and withstand harsh operating conditions.
http://ball-bearings.online/categories/tapered-bearings?id_category=12
137. South Yorkshire Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.bespoke.software.grid-itc.com
138. Doncaster Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.custom-software.1tsolutions.com
139. Needle Roller Bearings
Needle roller bearings are roller bearings with cylindrical rollers that are small in diameter. In spite of their low cross section, needle roller bearings have a high load carrying capacity and are therefore extremely suitable for bearing arrangements where radial space is limited. SKF supplies needle roller bearings in different designs and a wide range of sizes, which are appropriate for different applications. In addition to customized designs, they comprise the following types and components: needle roller and cage assemblies); drawn cup needle roller bearings; with open ends and with a closed end; full complement with open ends; needle roller bearings with machined rings; with flanges (closure rings or integral flanges) on the outer ring, sealed or not sealed and with or without an inner ring; without flanges on the outer ring , not sealed and with or without an inner ring; alignment needle roller bearings; with and without an inner ring ; inner rings for needle roller bearings ; universal joint bearings ; needle rollers; combined needle roller bearings (separate section); needle roller / angular contact ball bearings ; needle roller / thrust ball bearings ; needle roller / cylindrical roller thrust bearings ; needle roller thrust bearings and bearing washers (separate section); needle roller and cage thrust assemblies and appropriate washers; needle roller thrust bearings with a centring spigot and appropriate washers.
http://ball-bearings.online
140. Surplus Bearings
We purchase bearings and transmission products in bulk. If you would like to dispose of surplus or bankrupt stock, sell in bulk or just clear some of your inventory, we would like to hear from you.
http://www.surplus-bearings.co.uk
141. Threadolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.threadolets.zx55.com
142. Cheap Bearings
Skate bearings can be used for most applications within the industry, skateboards, scooters, quads, longboards and inlines all use the same sized bearings, some bearings are measured on an ABEC scale ranging from 1 to 11 (in odd numbers) with 11 being the highest precision, however this does not account for the grade of material used which is also very important to the speed of a bearing. 2 bearings are used per wheel with a spacer in the middle. As usual all the best brands can be found at Skatehut. We supply good quality bearings at a low price. We carry from stock all types of bearings, including deep groove ball bearings, roller bearings, metric and imperial bearings, tapered roller bearings, spherical bearings and needle bearings plus many more. Last time i bought some bearings from a local supplier the old boy who worked there said he had done research in a previous job into bearings in similar applications to suspension i.e applications where the bearing never does a full rotation and the conclusion was that within reason any bearing will perform the same. The only difference comes from better sealing from the elements in a bike application. He seemed to think that bushings were the best option on bikes as you dont get a point load which in hindsight is what full sussers used to use and bearings kits were an "upgrade". Interestingly I don't remember ever having a problem with bushings.
http://ball-bearings.online
143. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/huddersfield-university-accomodation
144. Email Spam Filter
A spam filtering service suitable for small and medium businesses, the 1T Solutions Gatekeeper service is competitively priced, and removes over 95% of e-mail spam and viruses.
http://www.1t-s.com/spam-filter
145. INA Bearings
The Schaeffler Group's INA brand stands for the development and manufacture of rolling bearings, plain bearings and linear systems as well as precision components for the automotive industry for engines, transmissions and powertrains worldwide. For 60 years, INA brand products have stood for creative application solutions as well as top engineering and production expertise to the company's customers. INA bearings are offered as part of the products available from the Schaeffler Group, a company created by the collaboration of bearings manufacturers INA bearings and FAG bearings. Totalling 180 years in the bearing business, the combination of INA and FAG created a company that has fast become an industry leader, specialising in roller bearings as well as a range of other excellent products. The quality of bearings manufactured at the Schaeffler Group is unrivalled and you can order bearings to suit your needs from Nationwide Bearings. With innovative bearing solutions at the forefront of their productions, it's clear that the combination of experience from INA bearings and FAG bearings was a boon for the bearings industry. You'll find high quality, great value INA bearings here at Nationwide Bearings, offering reliability and functionality as well as a competitive price. Purchase your required INA bearings today and enjoy fantastic bearings from the Schaeffler Group.
http://ball-bearings.online
146. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.custom-software.1tsolutions.com
147. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.application-development.1tsolutions.com
148. Stainless Tube Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
149. Contact Management Software
Contact Manager provides a shared database for all your business contact information. Web-enabled for access from anywhere, with a Windows application for remote users supporting on-line and off-line use with advanced synchronisation features.
http://www.1t-s.com/contact-manager
150. Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
151. Barnsley Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.bespoke-software.1tsolutions.com
152. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.custom.software.abrt.com
153. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.software.devlopment.abrt.com
154. Rotherham Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.custom.software.1t-s.com
155. Ice Ledger, the first full accounting software for start-up companies
Ice Ledger is a comprehensive business accounting software for small to medium sized business that you can download for free and start using immediately. The system is FREE to use for a whole year. Accounting features include sales ledger, sales quotes, sales order processing, sales invoicing, purchase ledger, purchase enquiries, purchase order processing, purchase invoicing, nominal ledger, stock control, Intrastat reporting, multi-currency and much more ...
http://www.iceledger.com
156. Doncaster Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.software.devlopment.1tsolutions.com
157. Doncaster Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.software.devlopment.1tsolutions.com
158. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://student-accomodation-huddersfield.iam4share.co.uk/
159. Deep groove ball bearings with filling slots
Single row deep groove ball bearings with filling slots have a filling slot in both the inner and outer ring enabling more and larger balls to be incorporated than in standard deep groove ball bearings. Filling slot bearings have a higher radial load carrying capacity than bearings without filling slots, but their axial load carrying capacity is small. They are also unable to operate at such high speeds as bearings without filling slots. Depending on the main application for which they are used, deep groove ball bearings with filling slots have a cage or no cage.
http://ball-bearings.online?pg=rb-dgbb-fs
160. South Yorkshire Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.bespoke.software.abrt.com
161. Simply Bearings
With the premier SKF brand your requirement for high quality bearings are here. Naturally we supply other quality brands like NACHI, NTN, KOYO, NKE, UBC, FAG, INA, IKO,NIS, TIMKEN etc and have in excess of 35,000 products listed here. We are ISO9001:2008 official bearings and seal distributors and suppliers and are official IKO distributors. Secure Online Transactions with HSBC Card Payment Services, Paypal and Google Checkout. ISO 9001:2008 Quality Managed and Accredited. Simply Bearings Ltd The UK's Original Online Bearings and Seals suppliers.
http://ball-bearings.online
162. Stainless Steel Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
163. Huddersfield University Student Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/huddersfield-university-student-accomodation
164. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.software.devlopment.grid-itc.com
165. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.custom.software.grid-itc.com
166. Barnsley Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.custom.software.grid-itc.com
167. Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://low-pressure-bsp-fittings.stainless-steel.zx55.com
168. Barnsley Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.barnsley.open-source.1t-s.com
169. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.bespoke-software.1tsolutions.com
170. Stainless Steel Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://butt-weld-fittings.stainless-steel.zx55.com
Rotherham Custom Software - Stainless Steel Low Pressure Fittings - Skip Hire System - Custom Software - Bespoke Software - SKF Bearings
Stainless Steel Low Pressure BSP Fittings - Upset Forging - Steel Forging - Forging Steel - SKF Bearings - Chesterfield Software Development
Web Design - Student Accomodation Huddersfield - Rotherham Linux - Doncaster Bespoke Software - Rooms For Rent Huddersfield - Doncaster Custom Software
Computer Repair - South Yorkshire eCommerce - Weldolets - Stainless Steel Butt-Weld Fittings - Computer Repair - Spherical Roller Bearings
Doncaster Bespoke Software - Chesterfield Application Development - Chesterfield Web Design - Koyo Bearings - Computer Systems - Stainless Steel Low Pressure Fittings
Student Accomodation Huddersfield - Barnsley Application Development - Doncaster Linux - Stainless Steel Hygienic Fittings - Weldolets - Rooms For Rent Huddersfield
Barnsley Bespoke Software - Sheffield Custom Software - Stainless Tube Supplier - Butt-Weld Fittings - Sockolets - Doncaster Web Design
Roll Forging - Computer Services - Press Forging - Smith Forging - Huddersfield University Accomodation - Deep groove ball bearings with filling slots
Rotherham Bespoke Software - Swaging - Sanitary Fittings - - Ball and Roller Bearings - Sanitary Fittings
Stainless Steel Flange Gaskets - Weldolets - Stainless Steel Butt-Weld Fittings - 304 Stainless Steel - Stainless Steel Forging - Application Development
Computer Maintenance - Computer Repair - Chesterfield Bespoke Software - Sheffield Software Development - South Yorkshire Application Development - Barnsley Bespoke Software
Low Pressure Fittings - Stainless Steel Gaskets - Sheffield Software Development - Computer Support - Needle Roller Bearings - Hygienic Fittings
Ball Bearings - Student Diggs in Huddersfield - Custom Software - Software Development - Chesterfield Custom Software - Sheffield Computer Services
South Yorkshire Computer Services - Computer Maintenance - South Yorkshire Bespoke Software - Chesterfield Software Development - Doncaster Custom Software - Rotherham Software Development
Sheffield Application Development - Ball Bearings - Email Spam Filter - Skip Manager - Stainless Steel Tubing - Cold Forming
Axle Bearings - Student Accomodation Huddersfield - SKF Bearings Catalogue - Self Lube Bearings - Huddersfield Student Housing - Drop Forging
South Yorkshire Bespoke Software - Skip Hire Software - Simply Bearings - Chesterfield Application Development - Rotherham Open Source - Bespoke Software
Bespoke Software - Rooms For Rent Huddersfield - Chesterfield Custom Software - Barnsley Bespoke Software - Rotherham Software Development - Waste Management System
Software Development - Stainless Steel Hygienic Fittings - Student Accomodation Huddersfield - Chesterfield Bespoke Software - Upset Forging - Suzuki Vehicle Bearings
South Yorkshire Computer Services - Surplus Bearings - Doncaster Bespoke Software - Mosque Message Display Board - Sheffield Custom Software - South Yorkshire Software Development
Cold Forming - Mosque Prayer Times - Stainless Steel Fittings - Barnsley Application Development - Rotherham Bespoke Software - Doncaster Bespoke Software
House For Rent Huddersfield - Barnsley Bespoke Software - Steel Forging - South Yorkshire Web Design - 316 Stainless Steel - Surplus Bearings
Waste Recycling System - Sheffield Custom Software - Computer Services - Waste Management Software - South Yorkshire Bespoke Software - Skip Hire News
Software Development - Barnsley Bespoke Software - Rotherham Computer Services - Cold Forming - Application Development - Custom Software
Sheffield Application Development - Engineering Blacksmiths - South Yorkshire Custom Software - Computer Support