1. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://house-for-rent-huddersfield.iam4rent.co.uk/
2. 304 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.304.stainless-steel.zx55.com
3. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.software.devlopment.1tsolutions.com
4. 316 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://316.stainless-steel.zx55.com
5. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/cheap-student-accomodation-huddersfield
6. Waste Management System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-management-system.skip-manager.co.uk
7. Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
8. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.software.devlopment.grid-itc.com
9. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.software.devlopment.grid-itc.com
10. Student Diggs in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/student-diggs-huddersfield
11. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/huddersfield-university-accomodation
12. Waste Collection System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-collection-system.skip-manager.com
13. Engineering Blacksmiths
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.ktforge.co.uk/engineering-blacksmiths
14. Skip Hire Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-hire-software.skip-manager.co.uk
15. Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://web-design.1t-s.com
16. Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.open-source.1t-s.com
17. Skip Manager
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-manager.co.uk
18. Stainless Steel Flange Gaskets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://flange-gaskets.stainless-steel.zx55.com
19. Sheffield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.bespoke.software.1t-s.com
20. Surplus Bearings
We purchase bearings and transmission products in bulk. If you would like to dispose of surplus or bankrupt stock, sell in bulk or just clear some of your inventory, we would like to hear from you.
http://www.surplus-bearings.co.uk
21. Waste Collection System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-collection-system.skip-manager.co.uk
22. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://software.development.abrt.com
23. Trailer Bearings
Trailer Bearings for all types of boat trailers - both tapered roller and ball bearings. The most popular bearings fitted to trailers are Tapered Roller Bearings. They come as two separate parts called the cup and cone. Some are supplied with a seal built in as an integral part of the bearing cone. Most bearings are stamped with an identification number by the manufacturer, If there are no numbers then the bearing can be identified by its dimensions - try typing the sizes in the search box. The most common bearings used on boat trailers are L44643 - L44610 and L44643L - L44610 Bearing number L44643 refers to the bearing cone without built in seal as shown on the left in both pictures. Bearing number L44643 L refers to the bearing cone with built in seal as shown on the right in both pictures. The same cup is used for both having the number L44610. Bearings for old style Mini hubs - these use ball bearings of the type 14/LJT 7/8" The bearings are a single row thrust bearing - 2" outside x 7/8" bore x 9/16" wide There are usually two bearings per hub with an oilseal which is 2.1/8" x 1.3/8" x 5/16".We supply both the bearings and oilseal - see our Online shop for prices.
http://ball-bearings.online
24. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.grid-itc.com/computer-support
25. Forging Stainless Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.ktforge.co.uk/forging-stainless-steel
26. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.software.devlopment.abrt.com
27. Cold Forming
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://www.ktforge.co.uk/cold-forming
28. Sockolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
29. Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://butt-weld-fittings.stainless-steel.zx55.com
30. Forging Stainless Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/forging-stainless-steel
31. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1tsolutions.com/application-development
32. Sheffield Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.sheffield.linux.1t-s.com
33. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://custom.software.1t-s.com
34. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://application-development.1tsolutions.com
35. Threadolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
36. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/
37. Smith Forging
Forging worked between flat or simple contour dies by repeated strokes and manipulation of the workpiece. Also known as "hand" or "flat die " forging.Heavy workpieces could be processed using a smith-forging hammer, and smaller forgings are die formed in drop hammers. Smith forging hammers are typically steam or air-operated, consisting of a power actuated ram supported by a heavy cast iron frame. The final product is a result of the ram being powered into the dies containing the workpiece.
http://www.kt-forge.co.uk/smith-forging
38. Upset Forging
Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.
http://www.kt-forge.co.uk/upset-forging
39. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.grid-itc.com/bespoke-software
40. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.bespoke.software.grid-itc.com
41. Skip Hire Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-hire-software.skip-manager.com
42.
Vauxhall Motors, commonly known as Vauxhall, is a British automotive manufacturer that has a long and storied history. Vauxhall was founded in 1857 by Alexander Wilson as a pump and marine engine manufacturer in Vauxhall, London, England. In 1903, Vauxhall produced its first automobile, a five-horsepower model, which was followed by the introduction of more advanced vehicles. In 1925, Vauxhall was acquired by General Motors (GM), an American automotive company. This marked the beginning of Vauxhall's affiliation with GM. Under GM's ownership, Vauxhall expanded its production capabilities and introduced a range of successful models, including the Vauxhall 10-4, Vauxhall Victor, and Vauxhall Viva. In 2017, General Motors sold its European division, including Vauxhall, to the PSA Group, a French automotive company that owns brands such as Peugeot and Citroën. Vauxhall continues to operate under the PSA Group and remains a prominent brand in the British automotive market. The company offers a diverse lineup of vehicles, including compact cars like the Vauxhall Corsa, mid-size cars like the Vauxhall Astra, SUVs like the Vauxhall Grandland X, and commercial vehicles like the Vauxhall Vivaro.
http://https://ball-bearings.online/oem/vauxhl/products
43. Jamat Times
Jamat Times, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Salah Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.
http://www.jamat-times.com
44. Thrust Bearings
A thrust bearing is a particular type of rotary bearing. Like other bearings they permit rotation between parts, but they are designed to support a high axial load while doing this. Thrust bearings come in several varieties. Thrust ball bearings, composed of ball bearings supported in a ring, can be used in low thrust applications where there is little axial load. Cylindrical thrust roller bearings consist of small cylindrical rollers arranged flat with their axes pointing to the axis of the bearing. They give very good carrying capacity and are cheap, but tend to wear due to the differences in radial speed and friction which is higher than with ball bearings. Tapered roller thrust bearings consist of small tapered rollers arranged so that their axes all converge at a point on the axis of the bearing. The length of the roller and the diameter of the wide and the narrow ends and the angle of rollers need to be carefully calculated to provide the correct taper so that each end of the roller rolls smoothly on the bearing face without skidding. These are the type most commonly used in automotive applications (to support the wheels of a motor car for example), where they are used in pairs to accommodate axial thrust in either direction, as well as radial loads. They can support rather larger thrust loads than the ball type due to the larger contact area, but are more expensive to manufacture. Spherical roller thrust bearings consists of two rings and asymmetrical rollers of spherical shape. They can accommodate combined radial and axial loads and also accommodate misalignment of the shafts. They are often used together with radial spherical roller bearings.
http://ball-bearings.online
45. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.bespoke.software.1t-s.com
46. Open Die Forging
Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.
http://www.ktforge.co.uk/open-die-forging
47. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.application-development.1tsolutions.com
48. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.abrt.com/custom-software
49. Roll Forging
Roll forging is a process where round or flat bar stock is reduced in thickness and increased in length. Roll forging is performed using two cylindrical or semi-cylindrical rolls, each containing one or more shaped grooves. A heated bar is inserted into the rolls and when it hits a stop the rolls rotate and the bar is progressively shaped as it is rolled through the machine. The piece is then transferred to the next set of grooves or turned around and reinserted into the same grooves. This continues until the desired shape and size is achieved. The advantage of this process is there is no flash and it imparts a favorable grain structure into the workpiece. Examples of products produced using this method include axles, tapered levers and leaf springs.
http://www.kt-forge.co.uk/roll-forging
50. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.application-development.1tsolutions.com
51. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/house-for-rent-huddersfield
52. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application.development.grid-itc.com
53. Skip Hire System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-hire-system.skip-manager.com
54. Huddersfield University Student Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/huddersfield-university-student-accomodation
55. Hammer Forging
The most common type of forging equipment is the hammer and anvil. Principles behind the hammer and anvil are still used today in drop-hammer equipment. The principle behind the machine is simple: raise the hammer and drop it or propel it into the workpiece, which rests on the anvil. The main variations between drop-hammers are in the way the hammer is powered; the most common being air and steam hammers. Drop-hammers usually operate in a vertical position. The main reason for this is excess energy (energy that isn't used to deform the workpiece) that isn't released as heat or sound needs to be transmitted to the foundation. Moreover, a large machine base is needed to absorb the impacts. To overcome some shortcomings of the drop-hammer, the counterblow machine or impactor is used. In a counterblow machine both the hammer and anvil move and the workpiece is held between them. Here excess energy becomes recoil. This allows the machine to work horizontally and have a smaller base. Other advantages include less noise, heat and vibration. It also produces a distinctly different flow pattern. Both of these machines can be used for open-die or closed-die forging. A forging press, often just called a press, is used for press forging.
http://hammer-forging.kt-forge.co.uk
56. Low Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://low-pressure-fittings.stainless-steel.zx55.com
57. Rotherham Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.software.devlopment.abrt.com
58. 316 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.316.stainless-steel.zx55.com
59. Hot Forging
Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.
http://www.ktforge.co.uk/hot-forging
60. Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://stainless-steel.zx55.com
61. Barnsley Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.application.development.1t-s.com
62. Barnsley Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.application-development.1tsolutions.com
63. House to Share Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://house-to-share-huddersfield.iam4share.co.uk/
64. Wheel Bearings Replacement
These instructions apply to bearings in a non-drive wheel. In other words, if your car is front wheel drive, we're talking about the rear bearings. If it's rear wheel drive, you'll be replacing the front wheel bearings. How do I know if I need new wheel bearings? Most of the time we don't even know that they need service. We just drive and never think about them. Most car manufacturers recommend a wheel bearing clean, inspection and repack every 30,000 miles. This is usually done along with the front brake service. They need to be replaced when there is scoring and pitting or they become noisy.
http://ball-bearings.online
65. Sheffield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.bespoke-software.1tsolutions.com
66. Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://linux.1t-s.com
67. 304 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
68. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.software.devlopment.1tsolutions.com
69. House to Share Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.student-housing-huddersfield.co.uk/
70. Accounts Software for Stockists
Designed for steel stock holders, SASS is a muli-currency accounts system which is ideal for all stockists incorporating Sales, Purchase & Nominal ledgers, Stock Control with emphasis traceability and profits based on actual / real costs ...
http://steelaccounts.com/
71. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.software.devlopment.1t-s.com
72. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.application.development.abrt.com
73. Waste Management System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-management-system.skip-manager.com
74. Sheffield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.custom-software.1tsolutions.com
75. Scooter Bearings
If you have plastic core scooter wheels then fitting the bearings is very straight forward as they typically can be pushed in by hand without issue. Fitting scooter bearings into Metal core wheels is a little trickier as they are designed to be a tight fit so pushing them in by hand rarely works. In our workshop we used to use a vise to gently squeeze them in, but now we use a hammer!! Apply a small amount of grease to the edges of each bearing you are going to install. Apply a small amount of grease to the inside hole on the scooter wheel where the bearings are going to be fitted. Place the bearing over the hole in the wheel and try and make sure that it is straight/level as possible. Place either a block of wood or an old paperback book over the top of the bearing and gently strike this with the hammer (Important - do not strike the bearing directly with the hammer). When the bearing has been hammered in fully into the hole in the middle of your wheel it should sit flush with the edge of the wheel Turn the wheel over and insert the bearing spacer (you will need a bearing spacer, if you do not use one your wheel will not spin when you do your axles up securely!)
http://ball-bearings.online
76. bicycle wheel bearings
The bicycle wheel bearings sit between a cone screwed to the wheel axle and the cup in the wheel hub. They must be properly adjusted and greased. To find out if they need greasing without taking everything apart, simply remove the wheel from the bike, support the axle horizontally with your fingers, and turn the wheel slowly--try not to tilt the axle as it rotates. If the wheel does not turn smoothly or you can feel tiny bumps in your fingers, then you must dismantle the bearing assembly and service the bearings. Get some good, flat, open wrenches. Make sure they are in sizes 13mm and 15mm. Those are the most common sizes. No other size wrench will work, but any type of adjustable wrench will do for the locking nut. Put the flat wrench on the bearing cone between the hub and the locking nut. Put the adjustable wrench on the locking nut. Hold the bearing cone in place and unscrew the locking nut. The best position to do this is hunched over the wheel while it sits on the ground. Whatever you do,do not open the cones at all while in this position. Just unlock it so you can unscrew everything with your fingers later. Grab the axle on the side that is still locked in place and point the end that you've just loosened, up. Now it is time to unscrew the locking nut almost completely off the axle. Next, unscrew the bearing cone to expose the wheel bearings to the light of day. Any grease in there? Re-grease. The fast way to re-grease your bearings is by just shooting grease in the bearings, screwing the cone back in, flipping the wheel over, hold the cone of the bearing you've just greased, grab the axle now facing up, unscrew it to reveal the other side's bearings and pack them with grease. But the proper way is by taking everything off, clean all the cones, hub cups, bearings, and repack with grease. Reassemble. Screw the bearing cone back into place, but not too tight. Bearings should be able to roll smoothly without axle play. Tighten the lock nut into place and check again.
http://ball-bearings.online
77. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/
78. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.application-development.1tsolutions.com
79. Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
80. Stainless Pipe Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
81. Cold Forming
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://cold-forming.kt-forge.co.uk
82. Chesterfield Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://chesterfield.linux.1t-s.com
83. Skip Hire Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-hire-software.com
84. Ice Ledger, Become a Partner and promote yourself and your organisation.
Ice Ledger is a comprehensive business accounting software for small to medium sized business that you can download for free and start using immediately. The system is FREE to use for a whole year. Accounting features include sales ledger, sales quotes, sales order processing, sales invoicing, purchase ledger, purchase enquiries, purchase order processing, purchase invoicing, nominal ledger, stock control, Intrastat reporting, multi-currency and much more ...
http://www.iceledger.com/partners
85. Stainless Pipe Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.stainless-pipe-supplier.zx55.com
86. SKF Bearings
SKF has a reputation for manufacturing high quality bearings. Most of our bearing and seal products are described in the SKF Interactive Engineering Catalogue. Information about other products may be included in other SKF websites. The left hand menu guides you to the right starting point. You can find online tools for product selection, and installation and maintenance in the library. Products for specific industries and applications. If you are looking for a product for a certain industry or application (for example a seal for a slurry pump), go to industries. This is a way to find the product and service solutions specific to your needs. The SKF services portfolio.
http://ball-bearings.online
87. Engineering Blacksmiths
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/engineering-blacksmiths
88. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.software.devlopment.1tsolutions.com
89. Sealed Bearings
Sealed bearings. A selection of SKF spherical roller bearings is also produced in a sealed version with contact seals on both sides. The seals are reinforced with sheet steel and made of an oil and wear-resistant: acrylonitrile-butadiene rubber (NBR), designation suffix 2CS; hydrogenated acrylonitrile butadiene rubber (HNBR), designation suffix 2CS5; fluoro rubber (FKM), designation suffix 2CS2. The seals are inserted in recesses in the outer ring. For smaller bearing sizes, the seals are pressed into the recesses while the seals for the larger sizes are held in position by means of retaining rings (fig). The seals have two sealing lips contacting the lead-in at the sides of the inner ring raceway, to provide efficient sealing. Sealed bearings are lubricated as standard with an extreme pressure bearing grease according to table 1. They should not be heated to temperatures above 80°C during mounting, and should not be washed. Sealed bearings do not need to be relubricated when the operating temperature does not exceed 70°C and the rotational speed is below 50% of the limiting speed listed in the product table. When temperature and/or speeds are high, relubrication with a similar grease with lithium thickener is recommended. In this case the polymer band, which covers the lubrication holes in the outer ring must be removed before mounting. Note that only a small amount of grease is needed to relubricate sealed bearings. The grease should be pressed in slowly through the lubrication holes in the outer ring while the bearing is rotating. Excessive pressure should be avoided so as not to damage the seals. The internal design of a sealed bearing corresponds to that of an open bearing. The external dimensions are also the same except for bearings based on the 222 and 223 series. These bearings are slightly wider and carry the series designation BS2-22 and BS2-23 respectively. Sealed bearings are available with a cylindrical bore as standard. However most bearings in the BS2-22 series are available with a tapered bore as well. Every sealed bearing can be supplied with a tapered bore to special order. To prevent interference with the seal, the diameter of the shaft abutment should not exceed damax at least for the 1 to 2 mm closest to the bearing. If the bearings are secured axially on the shaft by a lock nut, SKF recommends using a KMFE lock nut or to position an intermediate ring between the bearing and the lock nut.
http://ball-bearings.online
90. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.application.development.1t-s.com
91. South Yorkshire Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.software.devlopment.grid-itc.com
92. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.application.development.1t-s.com
93. Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
94. Stainless Steel Tubing
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://tubing.stainless-steel.zx55.com
95. Barnsley Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.application.development.grid-itc.com
96. Sheffield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.bespoke.software.grid-itc.com
97. Skip Hire System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-hire-software.skip-manager.com
98. South Yorkshire Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.software.devlopment.abrt.com
99. Wheel Bearings
Over time, wheel bearings suffer the effects of wear and tear. Water in particular takes its toll on them, making then rust or spoiling the grease that surrounds them. Wheel bearings allow your wheels to turn smoothly and also support the weight of the vehicle. If you're noticing alignment problems, your wheels are making a rumbling sound or the steering seems to have too much 'play' then you may have a wheel bearing problem and they may not be doing their job correctly. For quality wheel bearings for any car, check on line at eurocarparts.com and head off the danger of serious damage before it's too late.
http://ball-bearings.online
100. 316 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
101. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.software.devlopment.1t-s.com
102. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/house-for-rent-huddersfield
103. Stainless Steel Flanges
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
104. Stainless Steel Gaskets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://gaskets.stainless-steel.zx55.com
105. Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.butt-weld-fittings.stainless-steel.zx55.com
106. SKF Bearings Catalogue
The SKF online catalogue provides fast and easy access to parts and technical information. Features available through the SKF online catalogue range from basic product search to viewing product pictures, engine layouts, technical bulletins and much more. The SKF product portfolio. SKF has a reputation for manufacturing high quality bearings. Most of our bearing and seal products are described in the SKF Interactive Engineering Catalogue. Information about other products may be included in other SKF websites. The left hand menu guides you to the right starting point. You can find online tools for product selection, and installation and maintenance in the library. Products for specific industries and applications. If you are looking for a product for a certain industry or application (for example a seal for a slurry pump), go to industries. This is a way to find the product and service solutions specific to your needs. The SKF services portfolio. If you are looking for advice and services in the areas of engineering consultancy, logistics, asset management, condition monitoring, mechanical maintenance, remanufacturing, or training, go to services.
http://ball-bearings.online
107. Stainless Pipe Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
108. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application.development.1t-s.com
109. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.custom.software.1t-s.com
110. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.student-housing-huddersfield.co.uk/
111. Pillow Block Bearings
Plummer block roller bearing units. SKF roller bearing units (mounted bearings) with a plummer (pillow) block housing are available as: metric SKF ConCentra units; inch SKF ConCentra units; units with a locking collar. SKF ConCentra units in the SYNT series replace the former SKF ConCentra units in the SYT series. All plummer block roller bearing units comprise: a plummer block housing; an SKF spherical roller bearing in the 222 series; a stepped sleeve or locking collar; an integral seal fitted on both sides; lubricant. When compared to sleeve-mounted bearing units in split housings, SKF ConCentra units provide a number of advantages including: longer service life; higher operational reliability; quicker mounting; minimal maintenance; simplified replacement.
http://ball-bearings.online
112. Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.linux.1t-s.com
113. Chesterfield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.bespoke.software.1t-s.com
114. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/
115. Sockolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://sockolets.zx55.com
116. Cold Forming
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://www.kt-forge.co.uk/cold-forming
117. Bearings By Size
How to measure a bearing. Sometimes you may need to identify a bearing due to general wear and tear. Most bearing references now are laser stamped but these wear and rub off more quickly than the previous method, which was engraved deep in the bearing's metal. Bearing Sizes. Each bearing has an inside diameter, outside diameter and width diameter in that order. Most bearings are metric in size, but can also be imperial. On our site, each bearing shows its principal dimensions. d = Inside diameter, D = Outside diameter, B/T = Width diameter, You can search for a bearing entering this information on the home page in the boxes provided. Once you have identified the bearing's code some bearings come complete with seals or shields. This is known as the suffix in the bearings reference.
http://ball-bearings.online
118. Huddersfield University Student Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://huddersfield-university-student-accomodation.iam4share.co.uk/
119. Bearings Ltd
Looking for Bearings Ltd, look no further. Zx55.com stocks over 40,000 bearings for same day shipping, When it comes to bearing suppliers, zx55.com is the number one online bearings supplier that bearings ltd, bearing king, simply bearings and bearings boys cannot compare.
http://ball-bearings.online
120. Mercedes Benz Car Bearings
Mercedes-Benz, a German luxury automobile manufacturer, offers a diverse range of car models to cater to various segments and customer preferences. Mercedes-Benz car models include A-Class (entry-level compact car), C-Class (compact executive car), E-Class (mid-size luxury car), S-Class (full-size luxury sedan), GLE-Class (mid-size luxury SUV), GLC-Class (compact luxury SUV), GLA-Class (compact luxury SUV designed for urban environments), GLS-Class (full-size luxury SUV with three rows of seating), G-Class (or "G-Wagon" is a legendary off-road luxury SUV) and AMG Models (high-performance division of Mercedes-Benz). Mercedes-Benz regularly introduces new models and updates existing ones. The availability of specific models may vary by region and time.
http://ball-bearings.online/oem/merc/products
121. Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://hygienic-fittings.stainless-steel.zx55.com
122. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.bespoke.software.abrt.com
123. Doncaster Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.custom.software.1t-s.com
124. Rotherham Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.custom.software.grid-itc.com
125. Swaging
T=Swaging is a forging process in which the dimensions of an item are altered using a die or dies, into which the item is forced. Swaging is usually a cold working process; however, it is sometimes done as a hot working process. Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://swaging.ktforge.co.uk
126. Sheffield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.custom.software.1t-s.com
127. Opel Car Bearings
Opel is a German automobile manufacturer, founded by Adam Opel in 1862 as a manufacturer of sewing machines in Rüsselsheim, Germany. In 1899, Opel produced its first automobile, the Opel Patent Motor Car, marking its entry into the automotive industry. Opel quickly grew and became one of the largest automobile manufacturers in Germany by the early 20th century. Opel introduced various models, including the Opel 4/8 PS "Doktorwagen," which became a popular model. In 1929, Opel was acquired by General Motors (GM), introduing new models, including the Opel Kadett and Opel Olympia. After World War II, Opel played a significant role in the reconstruction of Germany's automotive industry. Opel introduced popular models like the Opel Rekord, Opel Kapitän, and Opel GT, gaining popularity both domestically and internationally. In the 1970s and 1980s, Opel expanded its lineup with models such as the Opel Manta, Opel Corsa, and Opel Omega. In 2017, General Motors sold Opel and its British sister brand, Vauxhall, to the PSA Group, a French automotive company that owns brands like Peugeot and Citroën. Opel became a part of the newly formed Stellantis N.V., the multinational automotive company resulting from the merger of PSA Group and Fiat Chrysler Automobiles (FCA) in 2021.
http://ball-bearings.online/oem/opel/products
128. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.sanitary-fittings.stainless-steel.zx55.com
129. Timeken
Timken Bearing Products. Timken is a leader in all bearing types, including standard anti-friction bearing configurations and advanced products such as housed units, integrated bearing assemblies, precision assemblies and FAA-approved aerospace bearings. Timken Roller Bearings, Tapered Roller Bearings, Spherical Roller Bearings, Cylindrical Roller Bearings, Precision Cylindrical Roller Bearings, Needle Roller Bearings, Thrust Roller Bearings, Timken Ball Bearings, Radial Ball Bearings, Angular Contact Bearings, Precision Bearings, Timken Spherical Plain Bearings, Radial Bearings, Radial Bearings with Lip Seals, Angular Contact Thrust Bearings, Timken High Performance Bearings, AquaSpexx® Trailer Wheel Bearing Kits, AquaSpexx® for Industrial Applications, DuraSpexx® and DuraSpexx® Power Rating Series, Thin Dense Chrome Bearings, Debris Resistant Bearings, Wear-Resistant Bearings, Low Torque Bearings, P900 Bearings, Timken Precision Bearings for Machine Tools, Super Precision Ball Bearings, Precision Tapered Roller Bearings, Ball Screw Support Bearings, Hydra-Rib Variable Preload Bearings, Precision Crossed Roller Bearings, Precision Cylindrical Roller Bearings, Timken Aerospace Bearings, Aerospace Ball Bearings, Aerospace Cylindrical Bearings, Aerospace Tapered Roller Bearings, Aerospace Spherical Roller Bearings, Aircraft Landing Wheel Bearings, Timken Integrated Bearing Assemblies, AP™ Integrated Bearing Assemblies, AP-2™ Integrated Bearing Assemblies, Formed Hub Wheel End System.
http://ball-bearings.online
130. Rooms For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/rooms-for-rent-huddersfield
131. Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/steel-forging
132. South Yorkshire Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.bespoke.software.1t-s.com
133. Fiat Car Bearings
Fiat, an Italian automobile manufacturer, has a long and storied history that spans over a century. Fiat, short for Fabbrica Italiana Automobili Torino, was founded on July 11, 1899, in Turin, Italy, by a group of investors led by Giovanni Agnelli. Fiat's first car, the Fiat 4 HP, was produced in 1899. It was a small, lightweight vehicle that helped establish Fiat's reputation for engineering and innovation. In the early 1900s, Fiat expanded its production capacity and introduced various models, including the Fiat 500 "Topolino" and the larger Fiat 508 "Balilla". Fiat experienced significant growth during the 1930s and 1940s, becoming the largest automobile manufacturer in Italy. Models such as the Fiat 1100 and the Fiat 500 "Cinquecento," both of which achieved widespread popularity. Fiat expanded internationally, establishing manufacturing facilities in several countries and acquiring other automotive companies like Lancia and Alfa Romeo. In the 1970s, Fiat continued to expand globally, forming partnerships with foreign manufacturers and establishing joint ventures, producing the Fiat Panda, Fiat Uno, and Fiat Tipo. Fiat also formed a partnership with the American manufacturer Chrysler in 2009, leading to the creation of Fiat Chrysler Automobiles (FCA) in 2014. Recent models include the Fiat 500 and the Fiat Panda gaining popularity. Fiat has also embraced electric mobility, introducing electric versions of its models, including the Fiat 500e.
http://ball-bearings.online/oem/fiat/products
134. Tapered Roller Bearings
Tapered roller bearings. Tapered roller bearings are produced by SKF in many designs and sizes to match their many uses. These can be grouped as follows: single row tapered roller bearings; paired single row tapered roller bearings; double row tapered roller bearings, and four-row tapered roller bearings. These are described in four separate sections under the appropriate headings. SKF also manufactures sealed, greased and pre-adjusted units based on tapered roller bearings, such as: hub bearing units for passenger cars; hub bearing units for trucks (fig), and tapered bearing units (fig) for railbound vehicles.
http://ball-bearings.online
135. South Yorkshire Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://south-yorkshire.open-source.1t-s.com
136. Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://steel-forging.ktforge.co.uk
137. Ice Ledger, the first full accounting software for start-up companies
Ice Ledger is a comprehensive business accounting software for small to medium sized business that you can download for free and start using immediately. The system is FREE to use for a whole year. Accounting features include sales ledger, sales quotes, sales order processing, sales invoicing, purchase ledger, purchase enquiries, purchase order processing, purchase invoicing, nominal ledger, stock control, Intrastat reporting, multi-currency and much more ...
http://www.iceledger.com
138. Computer Maintenance
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.grid-itc.com/computer-maintenance
139. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://software.development.1t-s.com
140. Ball Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
141. Waste Recycling System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-recycling-system.skip-manager.co.uk
142. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1t-s.com/bespoke-software
143. Barnsley Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.custom.software.abrt.com
144. Shaft Bearings
Shaft Bearings. Propeller and Rudder Shaft Bearings. Water lubricated rubber lined bearings for prop shafts and rudder shafts. Shaft Bearings (also known as Cutlass Bearings) are designed to be water lubricated. They are installed in the stern tube, or bearing housing and support the propeller shaft. The Drive Force range of water lubricated shaft bearings includes: Naval Brass cased shaft bearings, NEW GRP cased shaft bearings (non metallic), Phenolic cased shaft bearings (non metallic) will be replaced by GRP cased bearings, Composite cased shaft bearings (non metallic) will be replaced by GRP cased bearings, Special shaft bearings for Beneteau yachts
http://ball-bearings.online
145. South Yorkshire Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.bespoke.software.grid-itc.com
146. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.custom.software.abrt.com
147. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://custom.software.grid-itc.com
148. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/
149. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://student-accomodation-huddersfield.iam4rent.co.uk/
150. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/student-accomodation-huddersfield
151. Axle Bearings
Because axle shafts are typically made of softer steel than bearing rollers, shafts have a tendency to wear out before the bearing. The rollers can actually wear away a section of the shaft, as shown in the below diagram. Automotive cylindrical axle repair bearings are designed to replace the original bearings and seals on axles that are still in good condition, but whose original bearing and/or seal contact paths are not suitable for continued use. The extra-wide bearing repositions the rollers and seal to ride on unworn portions of the axle closer to the flange. Lubrication is accomplished through the axle tube by differential fluid, just like the OE design.
http://ball-bearings.online
152. Barnsley Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://barnsley.linux.1t-s.com
153. Waste Recycling Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-recycling-software.skip-manager.com
154. Doncaster Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.software.devlopment.grid-itc.com
155. IP WhoIs
The Detailed WhoIs tool not only checks the domain or IP address you request, but also looks up details of any associated domains and IP addresses, building a comprehensive report.
http://whois.1t-s.com
156. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://computer.support.1t-s.com
157. Stainless Steel Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.hygienic-fittings.stainless-steel.zx55.com
158. Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://1t-s.com/web-design
159. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1tsolutions.com/custom-software
160. Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
161. Smith Forging
Forging worked between flat or simple contour dies by repeated strokes and manipulation of the workpiece. Also known as "hand" or "flat die " forging.Heavy workpieces could be processed using a smith-forging hammer, and smaller forgings are die formed in drop hammers. Smith forging hammers are typically steam or air-operated, consisting of a power actuated ram supported by a heavy cast iron frame. The final product is a result of the ram being powered into the dies containing the workpiece.
http://www.ktforge.co.uk/smith-forging
162. Email Spam Filter
A spam filtering service suitable for small and medium businesses, the 1T Solutions Gatekeeper service is competitively priced, and removes over 95% of e-mail spam and viruses.
http://www.1t-s.com/spam-filter
163. Waste Recycling System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-recycling-system.skip-manager.com
164. Steel City Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
165. Chesterfield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.bespoke.software.grid-itc.com
166. Salat Timings
Salat Timings, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Jamat Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.
http://salat-timings.jamat-times.com
167. Stainless Steel Gaskets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.gaskets.stainless-steel.zx55.com
168. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/student-accomodation-huddersfield
169. Sheffield eCommerce
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.1t-s.com/internet-web-design
170. precision bearings
Machine tools and other precision applications require superior bearing performance. Extended speed capability, a high degree of running accuracy, high system rigidity, low heat generation, and low noise and vibration levels are just some of the performance challenges. To meet the ever-increasing performance requirements of precision applications, SKF and SNFA joined their precision bearing expertise to develop super-precision bearings. The new design super-precision angular contact ball bearings in the 718 (SEA) series are characterized by: high-speed capability, high stiffness, extended fatigue life, easy mounting, compact cross section. SKF-SNFA super-precision angular contact ball bearings in the 718 (SEA) series provide optimum performance in applications where there is a need for high reliability and superior accuracy. The bearings are particularly suitable for machine tool applications, multispindle drilling heads, robotic arms and measuring devices.
http://ball-bearings.online
171. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.application.development.abrt.com
172. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/huddersfield-university-accomodation
173. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
Chesterfield Linux - ZX55.com - Computer Services - Y-bearings with an eccentric locking collar - South Yorkshire Application Development - Doncaster Application Development
Custom Software - Hammer Forging - Rotherham Open Source - Chesterfield Application Development - Skip Hire News - South Yorkshire Software Development
Sheffield Application Development - Stainless Pipe Supplier - Swaging - Rooms For Rent Huddersfield - Custom Software - Press Forging
Doncaster Software Development - Student Accomodation in Huddersfield - Rotherham Computer Services - Chesterfield Bespoke Software - Online Bearings - Rotherham Custom Software
Stainless Steel Valves - Barnsley Open Source - Waste Collection System - Scooter Bearings - Huddersfield University Student Accomodation - Bearing Puller
Forging Stainless Steel - Sheffield Bespoke Software - Washing Machine Bearings - Stainless Steel Butt-Weld Fittings - Rotherham Software Development - Weldolets
Stainless Steel Fittings - Sheffield Application Development - Bespoke Software - Drop Forging - Web Design - South Yorkshire Computer Services
Hygienic Fittings - precision bearings - Computer Systems - Doncaster Software Development - Skip Hire Software - Barnsley Application Development
Inner Rings - Low Pressure BSP Fittings - Student Accomodation in Huddersfield - Ball Bearings - Huddersfield University Student Accomodation - Computer Services
Smith Forging - Steel Forging - Mosque Message Display Board - Alternative to Sage Accounts - South Yorkshire Software Development - Bearings By Size
Custom Software - Bespoke Software - South Yorkshire Open Source - Skip Hire System - Low Pressure Fittings - Ball Bearings
Rotherham Linux - Sheffield Bespoke Software - Stainless Steel Valves - Barnsley Application Development - Bespoke Software - South Yorkshire Open Source
Surplus Bearings - Bespoke Software - Custom Software - 304 Stainless Steel - Software Development - Computer Support
Hammer Forging - Steel Forging - Application Development - Barnsley Software Development - Ice Ledger, the first full accounting software for start-up companies - BMW Car Bearings
Rotherham Software Development - Rotherham Web Design - Chesterfield Custom Software - Doncaster Custom Software - Doncaster Software Development - Cold Forming
Salat Timings - South Yorkshire Bespoke Software - Stainless Steel Hygienic Fittings - Stainless Steel Tubing - Sheffield Custom Software - Steel Forging
Hot Forging - Forging Steel - Computer Services - Barnsley Custom Software - Stainless Steel Low Pressure BSP Fittings - Open Source
Barnsley Computer Services - Car Wheel Bearings - Bespoke Software - Smith Forging - Taper Bearings - House For Rent Huddersfield
Computer Maintenance - Stainless Steel Gaskets - Chesterfield Computer Services - Rotherham Application Development - Stainless Tube Supplier - Needle Bearings
Weldolets - Computer Support - Cold Forging - Barnsley Application Development - Timeken - Doncaster Custom Software
Press Forging - Ball and Roller Bearings - Rooms For Rent Huddersfield - Huddersfield Student Housing - Roller Bearings - Waste Management System
Rotherham Custom Software - Chesterfield Web Design - Rotherham eCommerce - Software Development - Needle Roller Bearings - Smith Forging
eCommerce - High Pressure Fittings - Computer Support - Chesterfield Application Development - Web Design - Threadolets
Skip Hire System - Computer Support - Application Development - South Yorkshire eCommerce - Forging Stainless Steel - Skip Manager
SKF Bearings Catalogue - Computer Maintenance - SKF Bearings - South Yorkshire Bespoke Software