1. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://computer.support.1t-s.com
2. Sealed Bearings
Sealed bearings. A selection of SKF spherical roller bearings is also produced in a sealed version with contact seals on both sides. The seals are reinforced with sheet steel and made of an oil and wear-resistant: acrylonitrile-butadiene rubber (NBR), designation suffix 2CS; hydrogenated acrylonitrile butadiene rubber (HNBR), designation suffix 2CS5; fluoro rubber (FKM), designation suffix 2CS2. The seals are inserted in recesses in the outer ring. For smaller bearing sizes, the seals are pressed into the recesses while the seals for the larger sizes are held in position by means of retaining rings (fig). The seals have two sealing lips contacting the lead-in at the sides of the inner ring raceway, to provide efficient sealing. Sealed bearings are lubricated as standard with an extreme pressure bearing grease according to table 1. They should not be heated to temperatures above 80°C during mounting, and should not be washed. Sealed bearings do not need to be relubricated when the operating temperature does not exceed 70°C and the rotational speed is below 50% of the limiting speed listed in the product table. When temperature and/or speeds are high, relubrication with a similar grease with lithium thickener is recommended. In this case the polymer band, which covers the lubrication holes in the outer ring must be removed before mounting. Note that only a small amount of grease is needed to relubricate sealed bearings. The grease should be pressed in slowly through the lubrication holes in the outer ring while the bearing is rotating. Excessive pressure should be avoided so as not to damage the seals. The internal design of a sealed bearing corresponds to that of an open bearing. The external dimensions are also the same except for bearings based on the 222 and 223 series. These bearings are slightly wider and carry the series designation BS2-22 and BS2-23 respectively. Sealed bearings are available with a cylindrical bore as standard. However most bearings in the BS2-22 series are available with a tapered bore as well. Every sealed bearing can be supplied with a tapered bore to special order. To prevent interference with the seal, the diameter of the shaft abutment should not exceed damax at least for the 1 to 2 mm closest to the bearing. If the bearings are secured axially on the shaft by a lock nut, SKF recommends using a KMFE lock nut or to position an intermediate ring between the bearing and the lock nut.
http://ball-bearings.online
3. Stainless Steel Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
4. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.application.development.grid-itc.com
5. Mercedes Benz Car Bearings
Mercedes-Benz, a German luxury automobile manufacturer, offers a diverse range of car models to cater to various segments and customer preferences. Mercedes-Benz car models include A-Class (entry-level compact car), C-Class (compact executive car), E-Class (mid-size luxury car), S-Class (full-size luxury sedan), GLE-Class (mid-size luxury SUV), GLC-Class (compact luxury SUV), GLA-Class (compact luxury SUV designed for urban environments), GLS-Class (full-size luxury SUV with three rows of seating), G-Class (or "G-Wagon" is a legendary off-road luxury SUV) and AMG Models (high-performance division of Mercedes-Benz). Mercedes-Benz regularly introduces new models and updates existing ones. The availability of specific models may vary by region and time.
http://ball-bearings.online/oem/merc/products
6. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.abrt.com/application-development
7. Open Die Forging
Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.
http://open-die-forging.kt-forge.co.uk
8. WhoIs
The Detailed WhoIs tool not only checks the domain or IP address you request, but also looks up details of any associated domains and IP addresses, building a comprehensive report.
http://whois.1t-s.com
9. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1t-s.com/custom-software
10. Ice Ledger, Become a Partner and promote yourself and your organisation.
Ice Ledger is a comprehensive business accounting software for small to medium sized business that you can download for free and start using immediately. The system is FREE to use for a whole year. Accounting features include sales ledger, sales quotes, sales order processing, sales invoicing, purchase ledger, purchase enquiries, purchase order processing, purchase invoicing, nominal ledger, stock control, Intrastat reporting, multi-currency and much more ...
http://www.iceledger.com/partners
11. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1tsolutions.com/application-development
12. Stainless Steel Tubing
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://tubing.stainless-steel.zx55.com
13. House to Share Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/house-to-share-huddersfield
14. Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://low-pressure-bsp-fittings.stainless-steel.zx55.com
15. Y-bearings with a standard inner ring
Y-bearings in the 17262(00)-2RS1 and 17263(00)-2RS1 series , with a standard inner ring, have Normal tolerances for the bearing bore diameter and are located on the shaft using an appropriate interference fit. The only difference between these Y-bearings and deep groove ball bearings in the 62 or 63 series is the sphered outside surface of the outer ring. These Y-bearings are suitable for applications where smooth running is a key operating requirement. These bearings can accommodate heavier axial loads than Y-bearings of any other design. The SKF range comprises bearings for metric shafts from 17 to 60 mm.
http://ball-bearings.online?pg=rb-yb-sir
16. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/house-for-rent-huddersfield
17. Wheel Bearings Replacement
These instructions apply to bearings in a non-drive wheel. In other words, if your car is front wheel drive, we're talking about the rear bearings. If it's rear wheel drive, you'll be replacing the front wheel bearings. How do I know if I need new wheel bearings? Most of the time we don't even know that they need service. We just drive and never think about them. Most car manufacturers recommend a wheel bearing clean, inspection and repack every 30,000 miles. This is usually done along with the front brake service. They need to be replaced when there is scoring and pitting or they become noisy.
http://ball-bearings.online
18. Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.stainless-steel.zx55.com
19. South Yorkshire Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.software.devlopment.abrt.com
20. Rooms For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://rooms-for-rent-huddersfield.iam4rent.co.uk/
21. Cold Forming
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://cold-forming.kt-forge.co.uk
22. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.software.devlopment.1t-s.com
23. Roll Forging
Roll forging is a process where round or flat bar stock is reduced in thickness and increased in length. Roll forging is performed using two cylindrical or semi-cylindrical rolls, each containing one or more shaped grooves. A heated bar is inserted into the rolls and when it hits a stop the rolls rotate and the bar is progressively shaped as it is rolled through the machine. The piece is then transferred to the next set of grooves or turned around and reinserted into the same grooves. This continues until the desired shape and size is achieved. The advantage of this process is there is no flash and it imparts a favorable grain structure into the workpiece. Examples of products produced using this method include axles, tapered levers and leaf springs.
http://www.ktforge.co.uk/roll-forging
24. South Yorkshire Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.south-yorkshire.web-design.1t-s.com
25. Rotherham Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.rotherham.computer.service.1t-s.com
26. Forging Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/forging-steel
27. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.application.development.abrt.com
28. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1tsolutions.com/application-development
29. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.bespoke.software.abrt.com
30. Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://steel-forging.kt-forge.co.uk
31. Rotherham Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.software.devlopment.1tsolutions.com
32. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.student-housing-huddersfield.co.uk/
33. Stainless Tube Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.stainless-tube-supplier.zx55.com
34. Y-bearings with a tapered bore
Y-bearings in the YSA 2-2FK series have an inner ring extended on both sides and a tapered bore (taper 1:12) enabling them to be mounted on standard adapter sleeves in the H 23 series. The appropriate adapter sleeve is not part of the bearing and must be ordered separately. Y-bearings of this type are delivered exclusively with the rugged standard "Superagriseal" fitted with additional plain sheet steel flingers. The outer ring has two lubrication holes as standard. Mounting onto an adapter sleeve enables the bearings to operate at higher speeds, run more smoothly in applications where the direction of rotation is constant or alternating. The SKF range, which comprises bearings with bore diameter from 25 to 65 mm, fits adapter sleeves in the H 23 series for metric shafts ranging from 20 to 60 mm. These bearings can also be used on adapter sleeves in the HA 23, HE 23 and HS 23 series for inch shafts ranging from 3/4 to 2 3/8 inch diameter.
http://ball-bearings.online?pg=rb-yb-tb
35. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://application.development.abrt.com
36. Stainless Steel Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.low-pressure-bsp-fittings.stainless-steel.zx55.com
37. Barnsley eCommerce
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.1t-s.com/internet-web-design
38. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://grid-itc.com/computer-support
39. Doncaster eCommerce
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.1t-s.com/internet-web-design
40. Waste Collection System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-collection-system.skip-manager.com
41. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.computer.support.1t-s.com
42. Computer Maintenance
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://abrt.com/computer-maintenance
43. Ford Car Bearings
Ford cars use a variety of bearings in different parts of their vehicles. Some common types of bearings used in Ford cars include Wheel Bearings, Crankshaft Bearings, Transmission Bearings, Idler Bearings and Tensioner Bearings. It's important to note that the specific type and size of bearings used in Ford cars can vary depending on the model, year, and specific components. When replacing bearings, it's recommended to consult the vehicle's service manual or seek assistance from a qualified mechanic to ensure the correct bearings are selected.
http://ball-bearings.online/oem/ford/products
44. Jamat Times
Jamat Times, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Salah Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.
http://www.jamat-times.com
45. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.application.development.grid-itc.com
46. Rotherham Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.software.devlopment.1t-s.com
47. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/student-accomodation-huddersfield
48. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/huddersfield-university-accomodation
49. Taper Bearings
Tapered roller bearings are bearings that can take large axial forces (i.e., they are good thrust bearings) as well as being able to sustain large radial forces. The inner and outer ring raceways are segments of cones and the rollers are also made with a taper so that the conical surfaces of the raceways and the roller axes if projected, would all meet at a common point on the main axis of the bearing. This conical geometry is used as it gives a larger contact patch, which permits greater loads to be carried than with spherical (ball) bearings, while the geometry means that the tangential speeds of the surfaces of each of the rollers are the same as their raceways along the whole length of the contact patch and no differential scrubbing occurs. When a roller slides rather than rolls, it can generate wear at the roller-to-race interface, i.e. the differences in surface speeds creates a scrubbing action. Wear will degenerate the close tolerances normally held in the bearing and can lead to other problems. Much closer to pure rolling can be achieved in a tapered roller bearing and this avoids rapid wear. The rollers are guided by a flange on the inner ring. This stops the rollers from sliding out at high speed due to their momentum. The larger the half angles of these cones the larger the axial force that the bearing can sustain. Tapered roller bearings are separable and have the following components: outer ring, inner ring, and roller assembly (containing the rollers and a cage). The non-separable inner ring and roller assembly is called the cone, and the outer ring is called the cup. Internal clearance is established during mounting by the axial position of the cone relative to the cup.
http://ball-bearings.online
50. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.software.devlopment.grid-itc.com
51. Stainless Steel Flanges
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
52. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1t-s.com/custom-software
53. Stainless Steel Flange Gaskets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
54. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.custom.software.grid-itc.com
55. Cold Forging
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://cold-forging.kt-forge.co.uk
56. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
57. Forging Stainless Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://forging-stainless-steel.ktforge.co.uk
58. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/
59. Drop Forging
Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.
http://drop-forging.ktforge.co.uk
60. Double row deep groove ball bearings
SKF double row deep groove ball bearings correspond in design to single row deep groove ball bearings. They have deep uninterrupted raceways and high conformity between the balls and raceways. They are able to carry axial loads acting in both directions in addition to radial loads. Double row deep groove ball bearings are very suitable for bearing arrangements where the load carrying capacity of a single row bearing is inadequate. For the same outside and bore diameters, double row bearings are slightly wider than single row bearings but have considerably higher load carrying capacity than single row bearings in the 62 and 63 series. DimensionsThe boundary dimensions of SKF double row deep groove bearings are in accordance with ISO 15:1998. TolerancesSKF double row deep groove ball bearings are produced to Normal tolerances. The values for tolerances correspond to ISO 492:2002. Internal clearanceSKF double row deep groove ball bearings have Normal radial internal clearance as standard. The clearance limits are as specified in ISO 5753:1991.
http://ball-bearings.online?pg=rb-dgbb-dr
61. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.software.devlopment.grid-itc.com
62. Cold Forging
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://cold-forging.ktforge.co.uk
63. Opel Car Bearings
Opel is a German automobile manufacturer, founded by Adam Opel in 1862 as a manufacturer of sewing machines in Rüsselsheim, Germany. In 1899, Opel produced its first automobile, the Opel Patent Motor Car, marking its entry into the automotive industry. Opel quickly grew and became one of the largest automobile manufacturers in Germany by the early 20th century. Opel introduced various models, including the Opel 4/8 PS "Doktorwagen," which became a popular model. In 1929, Opel was acquired by General Motors (GM), introduing new models, including the Opel Kadett and Opel Olympia. After World War II, Opel played a significant role in the reconstruction of Germany's automotive industry. Opel introduced popular models like the Opel Rekord, Opel Kapitän, and Opel GT, gaining popularity both domestically and internationally. In the 1970s and 1980s, Opel expanded its lineup with models such as the Opel Manta, Opel Corsa, and Opel Omega. In 2017, General Motors sold Opel and its British sister brand, Vauxhall, to the PSA Group, a French automotive company that owns brands like Peugeot and Citroën. Opel became a part of the newly formed Stellantis N.V., the multinational automotive company resulting from the merger of PSA Group and Fiat Chrysler Automobiles (FCA) in 2021.
http://ball-bearings.online/oem/opel/products
64. Skip Hire Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-hire-software.skip-manager.co.uk
65. Rooms For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/rooms-for-rent-huddersfield
66. Shaft Bearings
Shaft Bearings. Propeller and Rudder Shaft Bearings. Water lubricated rubber lined bearings for prop shafts and rudder shafts. Shaft Bearings (also known as Cutlass Bearings) are designed to be water lubricated. They are installed in the stern tube, or bearing housing and support the propeller shaft. The Drive Force range of water lubricated shaft bearings includes: Naval Brass cased shaft bearings, NEW GRP cased shaft bearings (non metallic), Phenolic cased shaft bearings (non metallic) will be replaced by GRP cased bearings, Composite cased shaft bearings (non metallic) will be replaced by GRP cased bearings, Special shaft bearings for Beneteau yachts
http://ball-bearings.online
67. Barnsley Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.custom.software.grid-itc.com
68. Chesterfield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.bespoke.software.grid-itc.com
69. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application-development.1tsolutions.com
70. Hot Forming
Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.
http://hot-forming.ktforge.co.uk
71. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/house-for-rent-huddersfield
72. Business Contact Manager
Contact Manager provides a shared database for all your business contact information. Web-enabled for access from anywhere, with a Windows application for remote users supporting on-line and off-line use with advanced synchronisation features.
http://www.1t-s.com/contact-manager
73. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.grid-itc.com/computer-support
74. Sheffield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.application.development.1t-s.com
75. Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.computer.service.1t-s.com
76. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1tsolutions.com/software-development
77. Stainless Steel Gaskets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.gaskets.stainless-steel.zx55.com
78. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://bespoke.software.grid-itc.com
79. Upset Forging
Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.
http://upset-forging.kt-forge.co.uk
80. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.application-development.1tsolutions.com
81. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.application.development.grid-itc.com
82. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
83. Computer Systems
Suppliers of computer systems and software from all the major vendors, 1T Solutions offers competitive pricing on computer hardware and shrink-wrapped application software.
http://www.1t-s.com/systems-software
84. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.software.devlopment.1tsolutions.com
85. House to Share Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://house-to-share-huddersfield.iam4share.co.uk/
86. 304 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
87. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.software.devlopment.abrt.com
88. 316 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
89. Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://grid-itc.com/computer-services
90. Y-bearings with grub screw locking
Y-bearings with grub screws in the inner ring are locked in position on the shaft by tightening the two cup point hexagonal grub (set) screws, positioned 120° apart. The bearings are suitable for applications where the direction of rotation is constant or alternating. Two different standard designs are available. Y-bearings in the YAT 2 series have an inner ring extended on one side , and are sealed with the rugged standard "Superagriseal" . The outer ring has two lubricating holes as standard. Y-bearings in the YAR 2 series have an extended inner ring on both sides . This reduces the extent to which the inner ring can tilt on the shaft, which enables the bearing to run more smoothly. These bearings are fitted with the rugged "Superagriseal", and one of the following flinger options
http://ball-bearings.online?pg=rb-yb-gsl
91. Sheffield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.bespoke.software.1t-s.com
92. Stainless Steel Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
93. Bike Bearings
Taking good care of your mountain bike is of paramount importance. Mountainbikebearings.co.uk stock all types of mountain bike bearings including bottom bracket bearings, pivot bearings, headset bearings, hub bearings, we also have in stock DU bushes which are found in shocks. We offer the mountain bike bearings as a standard bearing, or stainless steel bearing in most applications. Mountain Bike Bearings also offer bearings in various makes such as SKF and INA. We also stock a lot of genuine Hope bearings for pro 2 and pro 3 hubs, headsets and bottom brackets, and we have a budget range for when price is an issue. These can all be purchased from our online shop with next day delivery direct from our warehouse.
http://ball-bearings.online
94. Bearings for Alfa-Romeo Vehicles
Alfa Romeo, the Italian automotive manufacturer, uses various types of bearings in their vehicles, including hub bearings. While Alfa Romeo does not manufacture its own bearings, they source them from reputable bearing manufacturers that meet their quality standards. The specific types of bearings used in Alfa Romeo vehicles may vary depending on the model and the year of production. However, some common types of bearings found in Alfa Romeo vehicles including Hub Bearings, Tapered Roller Bearings and Ball Bearings. When it comes to maintenance or replacement of bearings in an Alfa Romeo vehicle, it is recommended to use high-quality bearings from trusted manufacturers that meet the specifications provided by Alfa Romeo. This ensures compatibility, reliability, and optimal performance of the bearings within the vehicle's system.
http://ball-bearings.online/oem/alfar/products
95. Rotherham Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.bespoke-software.1tsolutions.com
96. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.custom.software.grid-itc.com
97. Stainless Steel Flange Gaskets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://flange-gaskets.stainless-steel.zx55.com
98. Barnsley Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://barnsley.web-design.1t-s.com
99. Rotherham Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://rotherham.open-source.1t-s.com
100. Stainless Steel Pipes
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
101. Skip Manager
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-manager.co.uk
102. Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/steel-forging
103. Barnsley Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.application-development.1tsolutions.com
104. Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://forging.ktforge.co.uk
105. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.bespoke.software.grid-itc.com
106. Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://web-design.1t-s.com
107. Waste Recycling System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-system.skip-manager.co.uk
108. Rotherham Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.rotherham.linux.1t-s.com
109. Barnsley Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.custom-software.1tsolutions.com
110. Low Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
111. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://application-development.1tsolutions.com
112. Ball and Roller Bearings
A rolling-element bearing, also known as a rolling bearing, is a bearing which carries a load by placing round elements between two bearing rings. The relative motion of the pieces causes the round elements to roll with very little rolling resistance and with little sliding. One of the earliest and best-known rolling-element bearings are sets of logs laid on the ground with a large stone block on top. As the stone is pulled, the logs roll along the ground with little sliding friction. As each log comes out the back, it is moved to the front where the block then rolls on to it. It is possible to imitate such a bearing by placing several pens or pencils on a table and placing an item on top of them. See "bearings" for more on the historical development of bearings. A rolling element rotary bearing uses a shaft in a much larger hole, and cylinders called "rollers" tightly fill the space between the shaft and hole. As the shaft turns, each roller acts as the logs in the above example. However, since the bearing is round, the rollers never fall out from under the load.
http://ball-bearings.online
113. Stainless Steel Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.butt-weld-fittings.stainless-steel.zx55.com
114. South Yorkshire Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.bespoke.software.1t-s.com
115. Stainless Steel Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.hygienic-fittings.stainless-steel.zx55.com
116. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.software.devlopment.1tsolutions.com
117. Waste Recycling Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-software.skip-manager.com
118. Stainless Tube Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://stainless-tube-supplier.zx55.com
119. Replacement Bearings
BEARING REPLACEMENT GUIDE HELPS USERS CONVERT BEARINGS THAT HAVE BEEN WITHDRAWN OR ARE DIFFICULT TO SOURCE. NSK's new Bearing Replacement Guide is a comprehensive specification and selection guide, which enables bearing users to convert to NSK, bearings from other manufacturers that are in need of replacement, but have been withdrawn or are unavailable from the original supplier. The replacement guide includes some of the highest performing industrial and precision bearings available. Its layout and content have been specifically designed to help bearing users, machine re-builders and bearing distributors select the best type of replacement bearings for their applications.
http://ball-bearings.online
120. Stainless Steel Valves
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
121. Engineering Blacksmiths
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.ktforge.co.uk/engineering-blacksmiths
122. Open Die Forging
Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.
http://open-die-forging.ktforge.co.uk
123. Drop Forging
Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.
http://www.kt-forge.co.uk/drop-forging
124. Skip Hire News
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-hire-news.co.uk
125. Skip Hire Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-hire-software.skip-manager.com
126. Waste Collection System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-collection-system.skip-manager.co.uk
127. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1t-s.com/software-development
128. Sheffield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.custom.software.1t-s.com
129. Timeken
Timken Bearing Products. Timken is a leader in all bearing types, including standard anti-friction bearing configurations and advanced products such as housed units, integrated bearing assemblies, precision assemblies and FAA-approved aerospace bearings. Timken Roller Bearings, Tapered Roller Bearings, Spherical Roller Bearings, Cylindrical Roller Bearings, Precision Cylindrical Roller Bearings, Needle Roller Bearings, Thrust Roller Bearings, Timken Ball Bearings, Radial Ball Bearings, Angular Contact Bearings, Precision Bearings, Timken Spherical Plain Bearings, Radial Bearings, Radial Bearings with Lip Seals, Angular Contact Thrust Bearings, Timken High Performance Bearings, AquaSpexx® Trailer Wheel Bearing Kits, AquaSpexx® for Industrial Applications, DuraSpexx® and DuraSpexx® Power Rating Series, Thin Dense Chrome Bearings, Debris Resistant Bearings, Wear-Resistant Bearings, Low Torque Bearings, P900 Bearings, Timken Precision Bearings for Machine Tools, Super Precision Ball Bearings, Precision Tapered Roller Bearings, Ball Screw Support Bearings, Hydra-Rib Variable Preload Bearings, Precision Crossed Roller Bearings, Precision Cylindrical Roller Bearings, Timken Aerospace Bearings, Aerospace Ball Bearings, Aerospace Cylindrical Bearings, Aerospace Tapered Roller Bearings, Aerospace Spherical Roller Bearings, Aircraft Landing Wheel Bearings, Timken Integrated Bearing Assemblies, AP™ Integrated Bearing Assemblies, AP-2™ Integrated Bearing Assemblies, Formed Hub Wheel End System.
http://ball-bearings.online
130. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.bespoke.software.abrt.com
131. Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.linux.1t-s.com
132. Rooms For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/rooms-for-rent-huddersfield
133. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://custom.software.abrt.com
134. Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
135. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.application-development.1tsolutions.com
136. South Yorkshire Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.application.development.1t-s.com
Computer Maintenance - Forging Steel - 316 Stainless Steel - Rotherham Custom Software - Stainless steel deep groove ball bearings - Stainless Steel Hygienic Fittings
Computer Maintenance - Roll Forging - IT Services - Web Design - South Yorkshire Software Development - Ferrari Car Bearings
Rotherham Linux - Stainless Tube Supplier - Spherical Roller Bearings - Doncaster Custom Software - Custom Software - Application Development
Barnsley Software Development - Waste Collection System - Hammer Forging - Sheffield Custom Software - Application Development - Skip Hire News
Rotherham Custom Software - Chesterfield Linux - Butt-Weld Fittings - - Stainless Tube Supplier - Student Accomodation Huddersfield
Chesterfield Application Development - Stainless Steel Gaskets - Threadolets - Rotherham Bespoke Software - Steel Forging - Needle Bearings
Doncaster Bespoke Software - Deep groove ball bearings - SKF Bearings - Cold Forging - Rooms For Rent Huddersfield - Rotherham Web Design
Cheap Bearings - Chesterfield Bespoke Software - Chesterfield Software Development - Low Pressure BSP Fittings - Stainless Steel Low Pressure Fittings - Stainless Steel Pipes
Skip Hire Software - South Yorkshire Software Development - Student Accomodation Huddersfield - Chesterfield Bespoke Software - Forging Steel - Computer Repair
Application Development - Waste Collection Software - Application Development - Doncaster eCommerce - Waste Recycling System - Msajid Prayer Times
Huddersfield Student Housing - Free Accounts Software - Custom Software - Huddersfield University Student Accomodation - Student Diggs in Huddersfield - Application Development
Sheffield Computer Services - Computer Systems - Waste Recycling System - Custom Software - Rotherham Software Development - Stainless Steel Low Pressure BSP Fittings
Barnsley Application Development - Computer Repair - Hygienic Fittings - Stainless Steel High Pressure Fittings - Chesterfield Software Development - South Yorkshire Software Development
Software Development - Stainless Steel Forging - 304 Stainless Steel - Computer Maintenance - Rotherham Software Development - Skip Hire News
South Yorkshire Software Development - Washing Machine Bearings - Waste Collection Software - Upset Forging - Threadolets - Student Accomodation in Huddersfield
Chesterfield Application Development - Bespoke Accounts Software - Skip Hire Software - Skip Hire Software - Stainless Pipe Supplier - Software Development
Sockolets - Salat Timings - Rotherham Application Development - Doncaster Software Development - Stainless Steel Tubing - Rotherham Custom Software
Student Diggs in Huddersfield - Ball and Roller Bearings - South Yorkshire Software Development - Bearings - Computer Repair - Student Accomodation in Huddersfield
South Yorkshire Application Development - Computer Services - Threadolets - Stainless Steel Flange Gaskets - Hot Forging - Stainless Steel Butt-Weld Fittings
Computer Support - Rooms For Rent Huddersfield - Waste Management System - Cold Forging - Student Diggs in Huddersfield - INA Bearings
Swaging - Waste Management Software - Sheffield Open Source - Upset Forging - Rotherham Custom Software - Sheffield Application Development
Sheffield Bespoke Software - South Yorkshire Bespoke Software - Chesterfield Computer Services - High Pressure Fittings - Chesterfield Custom Software - Computer Support
Smith Forging - Doncaster Linux - Application Development - Student Accomodation Huddersfield - Student Accomodation in Huddersfield - Student Accomodation Huddersfield
Stainless Steel Tubing - Doncaster Software Development - Application Development - Chesterfield Application Development - Sheffield Web Design - South Yorkshire Custom Software
eCommerce - Computer Maintenance - House to Share Huddersfield - Stainless Steel Low Pressure Fittings - Hot Forging - Stainless Steel Valves
Custom Software - Stainless Steel Flanges - Rotherham Software Development - Anti-Spam - Bespoke Software - Hot Forming
Spam Filter - Doncaster Bespoke Software - Double row deep groove ball bearings - Mosque Prayer Times - Doncaster Application Development - Stainless Steel Forging
Replacement Bearings - Stainless Steel Hygienic Fittings - Smith Forging - Huddersfield University Accomodation - Salah Timetable - Rotherham Web Design
Y-bearings with a standard inner ring - BMW Car Bearings - Computer Repair - Chesterfield Custom Software - Rotherham Bespoke Software - Software Development
Chesterfield Web Design - Bike Bearings - Web Design - Bespoke Software - Rotherham Custom Software - Doncaster Open Source
Salaat Times - Press Forging - IT Support - Stainless Steel High Pressure Fittings - South Yorkshire Software Development - Stainless Steel Valves
Doncaster Custom Software - House to Share Huddersfield - Sheffield Software Development - Ball Bearings - Rotherham Open Source - Sheffield Bespoke Software
Barnsley Bespoke Software - Sheffield Custom Software - Student Accomodation Huddersfield - House For Rent Huddersfield - Doncaster Bespoke Software - Software Development
Rotherham Bespoke Software - Sheffield Software Development - RHP Bearings - Rotherham Bespoke Software - Sheffield Application Development - Cooper Split Bearings
Volkswagen Car Bearings - Bespoke Software - 316 Stainless Steel - House to Share Huddersfield - Barnsley Open Source - Software Development
Rotherham Software Development - Web Design - Email Spam Filter - Student Diggs in Huddersfield - Scooter Bearings - Chesterfield Software Development
Cold Forming - Barnsley Linux - Waste Collection System - Sheffield Software Development - Butt-Weld Fittings - Computer Maintenance
Sheffield Application Development - Stainless Steel Low Pressure BSP Fittings - 316 Stainless Steel - Barnsley Custom Software - Student Accomodation Huddersfield - Stainless Steel Forging
Rooms For Rent Huddersfield - Chesterfield Software Development - Press Forging - Drop Forging - Open Die Forging - Chesterfield Bespoke Software
Software Development - South Yorkshire Open Source - Sheffield Custom Software - Rotherham Open Source - Bearing NSK - Jamat Times
South Yorkshire Custom Software - Bespoke Software - Stainless Tube Supplier - Doncaster Application Development - Custom Software - Chesterfield Web Design
Linux - Rotherham Application Development - Custom Software - Chesterfield Custom Software - Open Die Forging - Bespoke Software